[GUIDE] How to remove SProtect & SSProtect

[Dragking]

The start of the guide says to open the map in mpq and see that its read only and then it says to open hxd and enter in some details but you dont specify which file to put into hxd

[nuzamacuxe]

It's the map, don't need to specify since it's obvious (I guess?).

[BlacklightsC]

Thanks to rewrite my thread. This thread more better.
Ps. Is any issue in my tool?

Ps 2. 0x7037AFC3 is hashed value at "(hash table)"
and also 0xA3B383EC is hashed value at "(block table)"

[nuzamacuxe]

Hey, long time no see. You're welcome!

Thank you very much! I've read your another guide as well (http://cheatmap.tistory.com/entry/7-Spr ... tSSProtect).

Your tool works just fine, didn't find any issue.

[BlacklightsC]

Thank you very much! I've read your another guide as well (http://cheatmap.tistory.com/entry/7-Spr ... tSSProtect).

That is not my writing. My friend edited a little bit.

P.S. He also can unhex as well, like me.

[nuzamacuxe]

Oh... I thought it was you, my bad. Sorry.

[clanhinata]

I read all your guide , its very clearly but i found something make confuse

The Length of Hash nd Block is x Header Pos(200) but Its you write x10 ?

[nuzamacuxe]

There are many ways to calculate the lenght, just do in the way you feel comfortable.

[clanhinata]

I mean in your thread :

The HEADER POS on START-OFFSET is 200 but the HEADER POS on Length is 10 , did u

The LENGTH of Hash Table on SProtect Example is : 04 00 * 02 00 = 80000 not 400 ?

On BlacklightsC Old Thread

Open Windows Calculator to Programmer mode.
Change to Hex, DWORD.
Start-offset = Header Pos + Hash/Block Pos
Length = Hash/Block Size * 10

Pos and Size must read little-endian
ex. 92 E9 A7 01 -> 01 A7 E9 92 -> 0x01A7E992

1) START-OFFSET & LENGTH VALUES:

NOTE: Don't forget to set your Windows calculator to DWORD.

• 1.1) To find the START-OFFSET of the HASH TABLE:
  HASH POS + HEADER POS (01 A7 E9 92 + 200) = 1 A7 EB 92

• 1.2) To find the LENGTH of the HASH TABLE:
  HASH SIZE * HEADER POS (4 00[400] * 10) = 4000

Here

• 1) START-OFFSET & LENGTH VALUES:
  
  NOTE: Don't forget to set your Windows calculator to DWORD.
  
  • To find the START-OFFSET of the BLOCK TABLE:
    BLOCK POS + HEADER POS (0 + 200) = 200
  • To find the LENGTH of the BLOCK TABLE:
    BLOCK SIZE * HEADER POS (2 94[294] * 10) = 2940

Here

1) START-OFFSET & LENGTH VALUES:

NOTE: Don't forget to set your Windows calculator to DWORD.

• 1.1) To find the START-OFFSET of the HASH TABLE:
  HASH POS + HEADER POS (FF E3 B4 14 + 1C4E00) = 214

• 1.2) To find the LENGTH of the HASH TABLE:
  HASH SIZE * HEADER POS (8 00[800] * 10) = 8000

And here

• 1) START-OFFSET & LENGTH VALUES:
  
  NOTE: Don't forget to set your Windows calculator to DWORD.
  
  • To find the START-OFFSET of the BLOCK TABLE:
    BLOCK POS + HEADER POS (FF E4 FC 16 + 1C4E00) = 1 4A 16
  • To find the LENGTH of the BLOCK TABLE:
    BLOCK SIZE * HEADER POS (4 06[406] * 10) = 4060

[/list]

[nuzamacuxe]

I see. This was a mistake, gonna fix it now. Thanks.