wc3edit.net

United Warcraft 3 map hacking!
It is currently September 23rd, 2018, 12:20 am

All times are UTC




Post new topic Reply to topic  [ 20 posts ]  Go to page Previous  1, 2
Author Message
PostPosted: April 17th, 2018, 5:07 am 
Offline
Newcomer

Joined: October 5th, 2009, 9:34 am
Posts: 9
The start of the guide says to open the map in mpq and see that its read only and then it says to open hxd and enter in some details but you dont specify which file to put into hxd


Top
 Profile  
 
PostPosted: April 17th, 2018, 5:08 am 
Offline
Moderator
User avatar

Joined: February 14th, 2018, 5:35 am
Posts: 506
Title: Just Another Mod
It's the map, don't need to specify since it's obvious (I guess?).


Top
 Profile  
 
PostPosted: April 25th, 2018, 10:20 pm 
Offline
Newcomer
User avatar

Joined: February 19th, 2015, 8:04 pm
Posts: 11
Location: Korea, Republic of
Title: Author to Cirnix
Thanks to rewrite my thread. This thread more better.
Ps. Is any issue in my tool?

Ps 2. 0x7037AFC3 is hashed value at "(hash table)"
and also 0xA3B383EC is hashed value at "(block table)"


Top
 Profile  
 
PostPosted: April 25th, 2018, 10:52 pm 
Offline
Moderator
User avatar

Joined: February 14th, 2018, 5:35 am
Posts: 506
Title: Just Another Mod
Hey, long time no see. You're welcome!

Thank you very much! I've read your another guide as well (http://cheatmap.tistory.com/entry/7-Spr ... tSSProtect).

Your tool works just fine, didn't find any issue.


Top
 Profile  
 
PostPosted: April 26th, 2018, 1:40 am 
Offline
Newcomer
User avatar

Joined: February 19th, 2015, 8:04 pm
Posts: 11
Location: Korea, Republic of
Title: Author to Cirnix
nuzamacuxe wrote:
Thank you very much! I've read your another guide as well (http://cheatmap.tistory.com/entry/7-Spr ... tSSProtect).


That is not my writing. My friend edited a little bit.

P.S. He also can unhex as well, like me.


Top
 Profile  
 
PostPosted: April 26th, 2018, 3:24 am 
Offline
Moderator
User avatar

Joined: February 14th, 2018, 5:35 am
Posts: 506
Title: Just Another Mod
Oh... I thought it was you, my bad. Sorry.


Top
 Profile  
 
PostPosted: July 23rd, 2018, 5:49 pm 
Offline
Member
User avatar

Joined: December 17th, 2011, 9:25 am
Posts: 95
Title: Just an old cheater
I read all your guide , its very clearly but i found something make confuse

The Length of Hash nd Block is x Header Pos(200) but Its you write x10 ?


Top
 Profile  
 
PostPosted: July 23rd, 2018, 6:21 pm 
Offline
Moderator
User avatar

Joined: February 14th, 2018, 5:35 am
Posts: 506
Title: Just Another Mod
There are many ways to calculate the lenght, just do in the way you feel comfortable.


Top
 Profile  
 
PostPosted: July 24th, 2018, 4:02 am 
Offline
Member
User avatar

Joined: December 17th, 2011, 9:25 am
Posts: 95
Title: Just an old cheater
I mean in your thread :

The HEADER POS on START-OFFSET is 200 but the HEADER POS on Length is 10 , did u

The LENGTH of Hash Table on SProtect Example is : 04 00 * 02 00 = 80000 not 400 ?

On BlacklightsC Old Thread

BlacklightsC wrote:
Open Windows Calculator to Programmer mode.
Change to Hex, DWORD.
Start-offset = Header Pos + Hash/Block Pos
Length = Hash/Block Size * 10

Pos and Size must read little-endian
ex. 92 E9 A7 01 -> 01 A7 E9 92 -> 0x01A7E992


nuzamacuxe wrote:

1) START-OFFSET & LENGTH VALUES:

NOTE: Don't forget to set your Windows calculator to DWORD.

    1.1) To find the START-OFFSET of the HASH TABLE:
    HASH POS + HEADER POS (01 A7 E9 92 + 200) = 1 A7 EB 92

    1.2) To find the LENGTH of the HASH TABLE:
    HASH SIZE * HEADER POS (4 00[400] * 10) = 4000

Here
nuzamacuxe wrote:
    1) START-OFFSET & LENGTH VALUES:

    NOTE: Don't forget to set your Windows calculator to DWORD.

      To find the START-OFFSET of the BLOCK TABLE:
      BLOCK POS + HEADER POS (0 + 200) = 200

      To find the LENGTH of the BLOCK TABLE:
      BLOCK SIZE * HEADER POS (2 94[294] * 10) = 2940


Here
nuzamacuxe wrote:

1) START-OFFSET & LENGTH VALUES:

NOTE: Don't forget to set your Windows calculator to DWORD.

    1.1) To find the START-OFFSET of the HASH TABLE:
    HASH POS + HEADER POS (FF E3 B4 14 + 1C4E00) = 214

    1.2) To find the LENGTH of the HASH TABLE:
    HASH SIZE * HEADER POS (8 00[800] * 10) = 8000


And here
nuzamacuxe wrote:

    1) START-OFFSET & LENGTH VALUES:

    NOTE: Don't forget to set your Windows calculator to DWORD.

      To find the START-OFFSET of the BLOCK TABLE:
      BLOCK POS + HEADER POS (FF E4 FC 16 + 1C4E00) = 1 4A 16

      To find the LENGTH of the BLOCK TABLE:
      BLOCK SIZE * HEADER POS (4 06[406] * 10) = 4060



Top
 Profile  
 
PostPosted: July 24th, 2018, 5:08 am 
Offline
Moderator
User avatar

Joined: February 14th, 2018, 5:35 am
Posts: 506
Title: Just Another Mod
I see. This was a mistake, gonna fix it now. Thanks.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 20 posts ]  Go to page Previous  1, 2

All times are UTC


Who is online

Users browsing this forum: No registered users and 12 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group

phpBB SEO


Privacy Policy Statement
Impressum (German)